to infinity best team about most wanted nokia xgold error

infinity team this was what ever when nokia xgold gives error in the middle
then no tool to revive this phones

but onlay mxbox has the sulution

one thing these logs are not to compare you with some other tool
best is the best 😀
these logs to show you to fix this error

please please please check

here is logs when best gives error

Quote:

Connect phone on selected interface…

Core : v2.23 , BB5XG FlashEngine : v10.1

Selected FlashSettings : Manual
Check FlashFiles, Please, wait…

Files Set for Flashing :
MCU : rm872__04.52.mcusw
PPM : rm872__04.52.ppm_m2
CNT : rm872__04.52.image_m2_059Q4J7
Flashing phone now…
[Gen] Rules accepted for : XGOLD Generation
Check files done…
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device…

-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge – just reinsert battery
-> If flashing freeze – reinsert cable/battery and try again
— Press phone’s power button or insert usb cable! —

Connection opened successfully

IF Boot Init : 0xF0
IF Resp Len : 0x0A
IF xCPUID : XGOLD 213 [XMM2130 QUANTUM]
IF Resp Data : 1FB300020303010100FF

Sending EBL Loader …
EBL Loader Ok, 01
EBL Loader ready, AA
Sending EBL …
EBL sent Ok
EBL : Quantum_Bootloader_10.53_M1S1
Speed accepted, use 6.500.000
FLASHID : 89008289
FLIC conf set, RST set
Boot done!

Check keys…
Check done. Image can be flashed

Backup enabled, will read all certificates

Reading CCC
Reading HWC
Reading NPC

IMEI 1 : 356324052112343
IMEI 2 : 356324052112350
PCcode : 059Q8L5

NPC Certificate saved…
CCC Certificate saved…
HWC Certificate saved…

RPL saved : C:\InfinityBox\BEST\Backup\Cert6324052112343_XG 213_CRT.rpl

Settings : EDM [0x8] , Block Mode , Fast CRC , Verify

===Flashing [MCU]===
File : rm872__04.52.mcusw
Image : rm872__04.52.mcusw_ebl_psi.fls
Sec-pack found, sending …
Sec-pack sent
Found 5 region(s)
Processing Region 1/5
Erase , Start : 0x40000000 , Len : 0x00020000
Erasing, wait …
Erase done, time : 00:00:01
Write , Start : 0x40000000 , Len : 0x00020000
Flashing , wait …
Region flash done, time : 00:00:00
Processing Region 2/5
Erase , Start : 0x40040000 , Len : 0x00020000
Erasing, wait …
Erase done, time : 00:00:01
Write , Start : 0x40040000 , Len : 0x00020000
Flashing , wait …
Region flash done, time : 00:00:00
Processing Region 3/5
Erase , Start : 0x40060000 , Len : 0x00100000
Erasing, wait …
Erase done, time : 00:00:06
Write , Start : 0x40060000 , Len : 0x00100000
Flashing , wait …
Region flash done, time : 00:00:01
Processing Region 4/5
Erase , Start : 0x40280000 , Len : 0x01800000
Erasing, wait …
Erase done, time : 00:01:45
Write , Start : 0x40280000 , Len : 0x01800000
Flashing , wait …
Region flash done, time : 00:00:32
Processing Region 5/5
Erase , Start : 0x43E20000 , Len : 0x00040000
[ERR_hReqFlashEraseStart] : 8201410040000000
Error…
-> Check cable, flashfile, try again from this file

Connect phone on selected interface…

Elapsed: 00:02:38
Connect phone on selected interface…


and here is mxbox success same set

Quote:

MXKEY [FT SCR2000 0], SN: C087289A
Using device: USB ROM
Connection status: UHCI:HUB:HUB::USB 1.10 (Full-speed)
Driver: NMWCD, ver: 7.1.32.117
Module ver: 1.0.0.21762(03-12-2014), Library ver: 1.0.0.14473(03-12-2014)
Make sure USB cable, Battery and charger are removed from device.
Insert USB cable, Battery back to device(make sure to have fully charged battery).
Insert Charger or Press phone’s power button(if flashing doesnt start automatically)
Waiting for USB ROM device …
Device synchronized.
CPU: XGOLD 213
Using embedded SBL from MCU.
Sending EBL Loader…OK
Sending EBL …OK
Getting EBL Version …
Boot mode: 0xCC
EBL version major/minor: 10.53
EBL version: Quantum_Bootloader_10.53_M1S1
Protocol version suggested by phone: 3
Set baud rate to: 6.50 Mbit/s
Flash ID: 0089 8982 – 23280001 [Intel NU48F512,512 Mbits]
CFI information:
Flash settings: 0/1024, size: 0x04000000
1 Block regions:
512 x 0x00020000 = 0x04000000
EBL ready !
Original IMEI: 35632405211234
RPL backup already exist (C:\mobileEx_1.5\data\backup\XGOLD_3563240521123 4_back.RPL)
Processing file: rm872__04.52.mcusw
Downloading item CODE:rm872__04.52.mcusw_ebl_psi.fls, num block: 4, size: 25.25 MB
Erasing area 0x40000000-0x4001FFFE …OK
Programming completed in 0.654 s
Erasing area 0x40040000-0x4005FFFE …OK
Programming completed in 0.682 s
Erasing area 0x40060000-0x4015FFFE …OK
Programming completed in 5.287 s
Erasing area 0x40280000-0x41A7FFFE …OK
Programming completed in 30.804 s
Checksum verified (0xFA4D)
Processing file: rm872__04.52.ppm_m2
Downloading item CUST:package_m2.ppm_ebl_psi.fls, num block: 1, size: 3.78 MB
Erasing area 0x41A80000-0x41E468EE …OK
Programming completed in 5.196 s
Checksum verified (0xC9E6)
Processing file: rm872__04.52.image_m2_059Q4J7
Downloading item CUST:package_m2_059Q4J7.image.fls, num block: 1, size: 16.25 MB
Erasing area 0x42100000-0x43E1FFFE …OK
Programming completed in 22.745 s
Checksum verified (0x5521)
Total time for flashing process(boot+erase+write) was 8 min 46.691 s
Waiting for USB device removal …
Waiting for device boot up …
Device connected: nmwcdc\Nokia X2-02 USB Phonet (), PORT_ID: 356324052112343
Verifying communication to device OK.

Phone type: RM-872 (206)
SW version: V 04.52 30-06-13 RM-872 (c) Nokia
Imei plain: 35632405211234-3
Product code: 059Q8L5
Language Pack:
– not available.

Imei net: 35632405211234
Version: SIMLOCK SERVER
Provider: GSM Test Operator
Counter: 0/3, 0/10

CONFIG_DATA: 0010100000000000
PROFILE_BITS: 800000000004000B

BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
FULL FACTORY… OK
USER DATA… OK
LEAVE FACTORY… OK
SERVICE CENTER… OK
SOFTWARE UPGRADE… OK
PRODUCTION TUNING… OK
Reset User Code (to default:12345) … OK
Completed in 0.121 s
FULL FACTORY… OK
USER DATA… OK
LEAVE FACTORY… OK
SERVICE CENTER… OK
SOFTWARE UPGRADE… OK
PRODUCTION TUNING… OK
Reset User Code (to default:12345) … OK
Completed in 0.345 s